LED Upgrade Kits for Legacy Display Walls

Upgrade for XL20/21/50 Series Cubes
Download Product Brochure

For legacy Mitsubishi display wall customers using select models of XL20 / XL21 and or XL50 type of lamp-based XGA or SXGA+ rear-projection cubes installed from years back, Mitsubishi Electric continues to strive for your continuous satisfaction by offering a unique opportunity for you to upgrade your existing display walls into state-of-the-art LED powered display walls.

For XGA customers, you even have the opportunity to upgrade to a higher resolution display wall, increasing your display real estate. All these as easy as swapping out your old engines to one of the new upgrade engine kits without having to reinstall new screens, new cabinets, or new walls! Upgrade today and say goodbye to tedious lamp changes and operational downtime for up to the next 10 years! .

Specifications


Key Features

Reduced System Upgrade Cost

The LED display wall upgrade can be realized by simply replacing the optical projection module and chassis unit. The cabinets, screens and other structures of existing display wall systems (base frames, claddings etc) can be continuously used. Therefore, no demolishing, construction and major interior change work are needed. Comparing with the whole display product / system replacement, the initial cost of investment is smaller. However, the display wall system can be upgraded to the latest LED-lit solution.

Low Cost of Ownership

1. Virtually Maintenance-free
LED light source has an average service life that is approximately 10 times longer than that of conventional ultrahigh-pressure mercury lamps. In addition, it does not require the colour wheel to create RGB colours. Combined with the 100,000hr, ultra-long service life of our fans, the average service life is more than 10 years, even when operated 24/7

2. Efficient Air Cooling System
The system has an optimal airflow path and cooling module design that are perfectly matched to the characteristics of the LED light source. Comparing with the liquid cooling system that requires periodical changes on the coolant, pump and drive parts, it has much less consumables.

3. Choice of Four Operating Modes
Equipped with an original LED power control circuit, each display wall product can be set to operate in one of four operating modes: Bright, Normal, Eco and Advanced Eco. Especially when operating under Eco or Advanced Eco mode, lower power consumption is achieved (XX W under Advanced Eco mode)..

Superior Performance by Mitsubishi Electricʼs Latest Technologies

1. Colour Space Control
To compensate for the colour and brightness inconsistencies on display wall products, Mitsubishi Electric has developed an original Colour Space Control Circuit that balances and blends colours. The ratios of each primary colour (Red/Green/Blue) and other colour mixtures are adjusted to provide consistent colour blending and superior uniformity on multi-screen configurations.

2. Dynamic Colour & Brightness Balancing
Each display wall product is equipped with three built-in sensors (one for each primary colour) that use a colour and brightness maintenance algorithm. The sensors continually monitor the individual red, green and blue output of each display wall product, share the data with adjacent displays, and adjust performance automatically to produce extremely accurate colours and brightness balance over the entire display. These features make it possible to maintain image uniformity on multi-screen configurations over long periods of operation without using external computers.

3. Choice of Four Operating Modes
Loss of brightness at the screen edges is no longer a problem owing to Mitsubishi Electric's innovative digital gradation circuit. Brightness is distributed evenly across the screen, ensuring the reproduction of sharp, vivid images from edge to edge on multi-screen configurations.

Wide Colour Reproduction Range by LED Light Source

The LED light source offers a much wider range of colour reproduction, allowing a larger array of vivid colours to be used for the icons and symbols frequently used in command and control rooms. This ultimately makes it easier for command and control room operators to share information.

Eco-conscious

The LED light source eliminates the use of mercury, and thus helps to preserve the environment. At the same time, the Eco mode setting contributes to lower power consumption and CO2 emissions than lamp-lit display wall products.

Applicable Models

VS-50XL20U
VS-50XL21U
VS-50XL50U
VS-50XLW20U
VS-50XLW50U
VS-50XLF20U
VS-50XLF50U
VS-50XLWF50U
VS-67XL20U
VS-67XL50U
VS-67XLW20U
VS-67XLW50U
VS-67XLF50U
VS-67XLWF50U
VS-50PH50U
VS-67PH50U
VS-67PHF50U

* Applicability for other models, please contact the nearest dealership.
* Depending on the installation situations, some upholstering work might be needed.
* Basically, the cabinets, screens and other structures of existing display wall systems (base frames, claddings etc) can be continuously used. However, depending on the conditions, some replacement might be necessary
.

Specification / VS-XE73RU

Display  
Display Type: LED Upgrade Kit for XL20/21/50 Series Cubes
LED Upgrade Kit for the following Mitsubishi XGA, lamp based Display Wall Cubes:
  • VS-50XL20U/21U/50U
  • VS-50XLW20U/50U
  • VS-50XLF20U/50U
  • VS-50XLWF50U
  • VS-67XL20U/21U/50U
  • VS-67XLW20U/50U
  • VS-67XLF20U/50U
  • VS-67XLWF50U
Display Technology:
  • DLP™ technology (0.7" DLP™ 1 chip) DarkChip3™
  • BrilliantColour™
Native Resolution: 1024 x 768 (XGA)
Screen Size:
  • 50" Diagonal Viewable
  • 67" Diagonal Viewable
Contrast Ratio: 1700:1
Interface  
RGB Input Scanning Frequency:
  • Resolution: VGA (640 x 480) – WUXGA (1920 x 1200)
  • Horizontal: 31.5kHz – 92kHz
  • Vertical: 49Hz – 85Hz
Pixel Clock Rate: 25MHz – 162MHz
Optional Input Signals (x3 slots):
  • VC-B70D2 - Input Board for Digital RGB Signals (DVI-D with HDCP x 2)
  • VC-B70DA2 - Input Board for Digital and Analog RGB Signals (DVI-I with HDCP x 2)
  • VC-B70G2 - Input Board for Analog RGB Signals (5 BNC x 1 / D-Sub mini 15 pin x 1)
  • VC-B70V2 - Input Board for Analog Video Signals (3 BNC x 2)
  • VC-B70DC - Input Board for Daisy Chain (D-Sub 15 x 1 / DVI-D with HDCP x 1 / 3 BNC x 1; Daisy chain output, no HDCP DVI-D x 1)
  • VC-B70SD1 - Input Board for SDI Signals (BNC x 1; through output BNC x 1)
Control Signal Inputs:
  • RS-232C: D-Sub 9 pins
  • LAN RJ45 x1
  • D-Sub 9 pins x 2 (input, output) Mitsubishi original control link
  • Wired Remote: F3.5 Jack
  • IR Receiver
Light Source  
Type: LED (RGB)
Estimated Lifetime:
  • 80,000 Hrs @ ECO Mode
  • 100,000 Hrs @ Advanced ECO Mode
Physical  
Voltage Range: AC 100 - 240V +/-10%, 50/ 60Hz +/-1Hz
Misc  
Temperature and Humidity: Condition at Operation:
  • 50°F-86°F (10°C-30°C) 20-80% non-condensing
Condition at Storage:
  • -4°F-122°F (-20°C-50°C) 20%-80% non-condensing
Safety Approval:
  • UL60950-1
  • CSAC22.2 No.60950-1
  • EN60950-1
  • K60950-1
  • AS60950-1
  • GB4943
EMC:
  • FCC part15 Subpart B Class A
  • ICES-003 Issue No.4 Class A
  • EN55022 Class A
  • EN55024
  • EN61000-3-2
  • EN61000-3-3
  • K00022 Class A
  • K00024
  • AS/NZS CISPR 22 Class A
  • GB9254 Class A
  • GB17625.1
  • VCCI Class A
  • JIS C 61000-3-2
Service & Support  
Service & Support
  • 2-Year Limited Parts and Labor Warranty.
  • 2-Year Limited Original LED-pack Warranty.

Specification / VS-PE73RU

Display  
Display Type: LED Upgrade Kit for XL20/21/50 Series Cubes
LED Upgrade Kit for the following Mitsubishi XGA, lamp based Display Wall Cubes:
  • VS-50XL20U/21U/50U
  • VS-50XLW20U/50U
  • VS-50XLF20U/50U
  • VS-50XLWF50U
  • VS-67XL20U/21U/50U
  • VS-67XLW20U/50U
  • VS-67XLF20U/50U
  • VS-67XLWF50U
Display Technology:
  • DLP™ technology (0.7" DLP™ 1 chip) DarkChip3™
  • BrilliantColour™
Native Resolution: 1400 x 1050 (SXGA+)
Screen Size:
  • 50" Diagonal Viewable
  • 67" Diagonal Viewable
Contrast Ratio: 1600:1
Interface  
RGB Input Scanning Frequency:
  • Resolution: VGA (640 x 480) – WUXGA (1920 x 1200)
  • Horizontal: 31.5kHz – 92kHz
  • Vertical: 49Hz – 85Hz
Pixel Clock Rate: 25MHz – 162MHz
Optional Input Signals (x3 slots):
  • VC-B70D2 - Input Board for Digital RGB Signals (DVI-D with HDCP x 2)
  • VC-B70DA2 - Input Board for Digital and Analog RGB Signals (DVI-I with HDCP x 2)
  • VC-B70G2 - Input Board for Analog RGB Signals (5 BNC x 1 / D-Sub mini 15 pin x 1)
  • VC-B70V2 - Input Board for Analog Video Signals (3 BNC x 2)
  • VC-B70DC - Input Board for Daisy Chain (D-Sub 15 x 1 / DVI-D with HDCP x 1 / 3 BNC x 1; Daisy chain output, no HDCP DVI-D x 1)
  • VC-B70SD1 - Input Board for SDI Signals (BNC x 1; through output BNC x 1)
Control Signal Inputs:
  • RS-232C: D-Sub 9 pins
  • LAN RJ45 x1
  • D-Sub 9 pins x 2 (input, output) Mitsubishi original control link
  • Wired Remote: F3.5 Jack
  • IR Receiver
Light Source  
Type: LED (RGB)
Estimated Lifetime:
  • 80,000 Hrs @ ECO Mode
  • 100,000 Hrs @ Advanced ECO Mode
Physical  
Voltage Range: AC 100 - 240V +/-10%, 50/ 60Hz +/-1Hz
Misc  
Temperature and Humidity: Condition at Operation:
  • 50°F-86°F (10°C-30°C) 20-80% non-condensing
Condition at Storage:
  • -4°F-122°F (-20°C-50°C) 20%-80% non-condensing
Safety Approval:
  • UL60950-1
  • CSAC22.2 No.60950-1
  • EN60950-1
  • K60950-1
  • AS60950-1
  • GB4943
EMC:
  • FCC part15 Subpart B Class A
  • ICES-003 Issue No.4 Class A
  • EN55022 Class A
  • EN55024
  • EN61000-3-2
  • EN61000-3-3
  • K00022 Class A
  • K00024
  • AS/NZS CISPR 22 Class A
  • GB9254 Class A
  • GB17625.1
  • VCCI Class A
  • JIS C 61000-3-2
Service & Support  
Service & Support
  • 2-Year Limited Parts and Labor Warranty.
  • 2-Year Limited Original LED-pack Warranty.